How to Properly Measure a Door Threshold Before Buying a Ramp | Complete Guide
How to Properly Measure a Door Threshold Before Buying a Ramp
How to Properly Measure a Door Threshold Before Buying a Ramp
Before purchasing a threshold ramp, it is essential to accurately measure the door threshold. Incorrect measurements can result in a ramp that is too high, unstable, or creates an unsafe approach angle.
Step 1. Measure the Exact Threshold Height
The height should be measured from the floor or ground level to the highest point of the threshold. Use a measuring tape or a level for precise results.
2–4 cm – low threshold
5 cm – standard threshold
7–10 cm – high threshold
This measurement determines which rubber threshold ramp model is suitable for your needs.
Step 2. Check the Available Depth in Front of the Door
Make sure there is sufficient space in front of the door to install the ramp. The greater the depth, the smoother the incline angle.
If space is limited, choose a model with an optimized height-to-length ratio.
Step 3. Consider the Type of Door
Check the following:
Will the ramp interfere with door opening?
Is there a rubber seal at the bottom of the door?
Is the threshold interior or exterior?
Step 4. Evaluate the Load Requirements
If the ramp will be used for:
a wheelchair
a baby stroller
carts or trolleys with goods
— you should select a model with adequate load capacity.
A stationary rubber threshold ramp supports over 500 kg and is suitable for daily use.
Step 5. Check the Required Width
The standard usable width of DPR ramps is typically between 90–110 cm, depending on the ramp height. If it is necessary to reduce the width of the door ramp, a utility knife can be used to trim the rubber material carefully.
Common Measuring Mistakes
Measuring from only one side
Ignoring floor slope
Not accounting for rubber door seals
Choosing a ramp “by eye” without precise measurement
Conclusion: Accurate threshold measurement is the foundation of safe access. A properly selected threshold ramp ensures comfort, stability, and long-term durability.
SOZI DPR25 Rubber Threshold Ramp – for 2.5 cm / 25 mm Thresholds
The SOZI DPR25 rubber threshold ramp is designed to provide a smoother and easier transition over low door thresholds, raised edges ..
SOZI DPR38 Rubber Threshold Ramp 3.8 cm / 38 mm – Stable and Smooth Access
SOZI DPR38 is a rubber threshold ramp with a height of 38 mm (3.8 cm), designed to provide a smoother and easier transitio..
SOZI DPR50 Rubber Threshold Ramp 5 cm / 50 mm – Stable Access Over Higher Thresholds
SOZI DPR50 is a rubber threshold ramp with a height of 50.8 mm (approximately 5 cm), designed to provide easier ..
SOZI DPR64 Rubber Threshold Ramp 6.4 cm / 2.5 Inch – for Higher Thresholds and Level Differences
SOZI DPR64 is a heavy-duty rubber threshold ramp with a height of 63.5 mm (approximately 6.4 cm / 2...
SOZI DPR76 Rubber Threshold Ramp 7.6 cm / 3 Inch – for Garages, Cars and Higher Level Differences
SOZI DPR76 is a heavy-duty rubber threshold ramp with a height of 76 mm (7.6 cm / approximately 3 i..
SOZI DPR89 Rubber Threshold Ramp 8.9 cm / 3.5 Inch – Solution for Higher Thresholds
SOZI DPR89 is a heavy-duty rubber threshold ramp with a height of 89 mm (8.9 cm / approximately 3.5 inches), desi..
SOZI DPR102 Rubber Threshold Ramp 10.2 cm / 4 Inch – for High Thresholds and Level Changes
SOZI DPR102 is a heavy-duty rubber threshold ramp with a height of 102 mm (10.2 cm / approximately 4 inche..
What Is the Correct Slope for a Threshold Ramp? Engineering Analysis with Real Calculations
When selecting a threshold ramp, most buyers focus only on height. However, a professional approach requi..
Rubber Threshold Ramp or Aluminum Ramp – Which Is the Right Choice?
When selecting a threshold ramp, the key question is not just the material — it is the intended use. Do you need a portable r..
EN 17210 and Ramp Slope – What Are the Requirements for a Threshold Ramp?
The European standard EN 17210 defines technical accessibility requirements for buildings. One of the most important pa..
Wheelchair Ramp – What Are the Technical Requirements?
Selecting or designing a wheelchair ramp is not simply a practical decision — it is a technical process that must ensure safety, stability..
Can a Rubber Threshold Ramp DPR Be Cut?
Yes. Every rubber threshold ramp in the DPR series can be trimmed in width when necessary. This allows precise adjustment to specific doorway openings or..
Does a Rubber Threshold Ramp Require Mechanical Fixing?
In most residential and commercial environments, a rubber threshold ramp DPR does not require mechanical fixing. Its weight and anti-slip..
